Entferner H – High-Pass Filter

Entferner H is a stereo, resonant, and self-oscillating 12/24dB high-pass filter.

Entferner filters, in general, are based on a cascade of very versatile 6dB filters. In the Entferner H filter, two or four of the filters are used and can be modulated either using the internal signal or any external CV.

Since the filter is using internal saturation, the sound is highly dependent on the input voltages. Red LED lights beside the ports indicate any voltage overdrive. If the LED is blinking from time to time, the filter is operating in its sweet spot. If the LED is continuously red, the filter will still work but might result in a harsh sound or unwanted behavior.

Notes

  • The self-oscillation is not pitch-perfect over the whole filter range.
  • Some aliasing may occur in case of extreme cutoff, resonance and/or drive values.
  • Audio rate modulation is possible, but the filter behaves differently to what you might expect.
ParameterDescription
CutoffThe cutoff frequency controls the spectral content of the sound. A cutoff can be entered in the range of 10Hz-18kHz.
Cutoff – SlopeSelect either a 12dB or 24dB slope. The higher the value the steeper the filter cuts the frequencies.
Cutoff – Internal ModulationControl the cutoff frequency based on the signal processed by the filter. Even using high modulation voltages will not increase the cutoff frequency above 18kHz. Take a look at the modulation source parameter for more information.
Cutoff – Internal Modulation SourceSelect which internal signal is used as a modulation source. It is either the summed PRE signal as it is coming in at the IN ports. Or it is the summed POST signal as it is coming out of the OUT ports. When pressed both buttons, the sum of the signals is used.
Cutoff – External ModulationControl the cutoff frequency based on the signal coming in at the external modulation port. A setting of ±100% equals 1V/oct. Even using high modulation voltages will not increase the cutoff frequency above 18kHz.
DriveDrive controls the amount of the internal saturation. Drive is entered in the range of ±100%. It will not drastically in-/decrease the overall volume of the filtered sound. When lowering the drive amount the resonance gets more prominent. When raising the drive the sound will get more saturated.
Drive – Internal ModulationControl the drive based on the signal processed by the filter. Take a look at the modulation source parameter for more information.
Drive – Internal Modulation SourceSelect which internal signal is used as a modulation source. It is either the summed PRE signal as it is coming in at the IN ports. Or it is the summed POST signal as it is coming out of the OUT ports. When pressed both buttons, the sum of the signals is used.
Drive – External ModulationControl the drive based on the signal coming in at the external modulation port.
ResonanceResonance controls the amount of feedback at the cutoff point in the spectral content. Resonance is entered in the range of 0%-100%. Where 0% is no resonance and 100% is the maximum. If the resonance is set to a high value the filter will start to self oscillate.
Resonance – ColorAlters the sound of the resonance.
Resonance – Internal ModulationControl the resonance based on the signal processed by the filter. Take a look at the modulation source parameter for more information.
Resonance – Internal Modulation SourceSelect which internal signal is used as a modulation source. It is either the summed PRE signal as it is coming in at the IN ports. Or it is the summed POST signal as it is coming out of the OUT ports. When pressed both buttons, the sum of the signals is used.
Resonance – External ModulationControl the resonance based on the signal coming in at the external modulation port. Even using extreme modulation voltages will not result in resonance outside of the allowed range.

Note: The Entferner filter package is sold via the VCV Rack library.

Note: The Entferner LE package is sold via the VCV Rack library.

Version History

Version 2.0.6 (2021-12-10)

  • Improved lights when the module is bypassed
  • Fixed: DRM issues when used in plugin mode

Version 2.0.5 (2021-12-04)

  • Rack 2.0 compatible version
  • Supports “Bypass”
  • Supports “Light bloom” settings
  • Optimized graphics performance (GPU usage)

Version 1.0.4 (2021-07-05)

  • Entferner L/H/B: fixed; some parameter changes caused an issue in the stereo signal

Version 1.0.3 (2020-07-07)

  • Entferner L/H/B: fixed; modulation could have caused a 0.0Hz cutoff frequency
  • added link to the online manual in the popup menu

Version 1.0.2 (2020-06-26)

  • Entferner L/H/B: performance improvements
  • Entferner L/H/B: optimized self-oscillation handling

Version 1.0.1 (2020-06-25)

  • Initial release

Copyright

Oxidlab holds the copyright for the product concept, algorithm, and support material (e.g., manual).

Visual Concept and Artwork: Chris Corrado